<track id="d7dff"></track>

        <dfn id="d7dff"></dfn>

            <rp id="d7dff"></rp>

            <strike id="d7dff"></strike>

            <cite id="d7dff"><th id="d7dff"></th></cite>




                如果您對該產品感興趣的話,可以 產品名稱: 計算機氣體校準系統
                產品型號: 6100
                產品展商: Environics
                產品文檔: 無相關文檔


                計算機氣體校準系統,環境氣體分析動態校準.The Series 6100 計算機氣體校準系統automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases of interest.


                6100型計算機多氣體校準系統, 計算機氣體校準系統,環境氣體分析動態校準
                The Environics® Series 6100 Computerized Multi-Gas Calibration System is a computer controlled, state-of-the-art instrument for dynamic calibration of ambient air analyzers. The Series 6100 automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases of interest. The 6100 meets all U.S. Environmental Protection Agency requirements.

                The Series 6100 計算機氣體校準系統consists of a single chassis supporting 2 thermal mass flow controllers, an ozone generation module, a mixing zone, a reaction chamber for gas phase titration, and control electronics.

                 Commands are entered from the front panel and displayed on a backlit 4 line by 20 character liquid crystal display. The instrument may also be remotely operated using contact closures or the RS-232 serial data interface, both are standard in the Series 6100.

                The mass flow controllers are calibrated to a NIST (National Institute of Standards and Technology) traceable primary standard. The calibration data consists of a comparison of desired versus actual flow over the full dynamic range of the instrument with linear interpolation between points. Calibration data is stored in non-volatile memory and may be updated by the user with a suitable standard.

                The Series 6100 ozone generator is factory calibrated using a NIST traceable ozone standard. This temperature controlled, ultra-violet (UV) based ozone generator includes a precision photo-optical feedback circuit to compensate for lamp aging effects.

                The Series 6100 is available in either a standard rack mount or portable configuration.



                User-friendly interactive software with plain language prompts is simple to use, reducing technician training time and virtually eliminating error.

                Automatic calculation of dilution and span gas flows based on commanded concentration eliminates the need for manual computation and allows rapid transition from point to point.

                Internally-stored mass flow controller calibration data improves accuracy by as much as a factor of ten and simplifies field recalibration. Mass flow controllers are factory calibrated at 11 points.

                Internally-stored ozone generator calibration data insures linear, repeatable ozone generation without photometer control. Ozone generator performance meets U.S. EPA criteria for ozone transfer standards.

                Ozone generator pressure compensation ensures repeatable and stable ozone generation at pressures other than the original calibration pressure.

                Full, two-way RS-232 Serial Data Interface (standard) permits remote operation of the instrument including data collection, gas selection, initiation of zero, span and multi-point calibrations.


                • Concentration Mode: In response to software prompting, user selects gas port, span (cylinder) gas concentration, output gas flow (total) and output gas concentration. Series 6100 automatically delivers concentrations at the total flow specified.
                • Generate Ozone: Allows user to specify, then generate a precise concentration of ozone.
                • Gas Phase Titration: Utilizes blend and generate ozone routines to lead user through GPT using "excess NO" method.
                • Flow Mode: Allows user to manually command a desired rate of flow for each mass flow controller, individually or together, and with or without ozone.
                • Display: Allows user to monitor flow rates for each mass flow controller separately. Also provides ozone oven block temperature during generate ozone and gas phase titration routines.
                • Maintain Ports: User enters the name of the span gas in the source cylinder, its concentration (ppm) and the port to which the cylinder is connected.



                  Accuracy     Concentration:         ?1.0% setpoint     Flow:                  ?1.0% setpoint  Flow Repeatability:       ?0.05% F.S.O.
                  Warm up time:  30 minutes
                * Performance specifications are valid when all Mass Flow Controllers are operating between 10% and 100% of full scale flow.
                Mass flow controllers are calibrated using a NIST traceable Primary Flow Standard, using a Reference Temperature of 25癈 (77癋) and a Reference Pressure of 760 mm Hg (29.92 in. Hg)
                Ozone Generator  Concentration Range:  0.02 - 0.5 ppm at 5 - 10 slpm  Optional Ranges:      0.05 - 1.0 ppm at 5 - 10 slpm
                  Accuracy:         +/- 2% or +/- 0.003 ppm  Repeatability:    +/- 2% or +/- 0.003 ppm (for 30 days)


                Inlets  Balance: External 1/4" Swagelok*  Span(s): External 1/4" Swagelok*
                Outlet    One external 1/4" Swagelok*
                  *(or compatible fitting)
                Operating Pressures at inlets    Minimum:       20 psig (1.38 Bar)    Nominal:       25 psig (1.72 Bar)    Maximum:       30 psig (2.07 Bar)
                Wetted Surfaces    Tubing:  Teflon®    MFCs:    Stainless Steel    Seals:   Viton®    Glass Chambers:  Pyrex®
                Operating temperatures    32?- 122?F (0?- 50?C)
                Performance Temperature Range    59?- 95?F (15?- 35?C)
                Weight    Standard:           20 lbs.    Including Options:  30 lbs.
                Dimensions (w x h x d)  Portable:  17" x 7" x 15"  Rack:      19" x 7" x 15"


                    Voltage: 100 to 250 VAC, 50/60 Hz    Current:  2 Amps (maximum)

                Operating Modes

                  Front panel keypad  Internal timer control  RS-232 serial data interface  I/O control (8 inputs / 8 outputs)

                Data I/O

                  RS-232 serial data interface  I/O Control (8 inputs / 8 outputs)

                Copyright? 2003-2022  培德國際有限公司上海代表處版權所有   聯系人:盧先生  聯系電話:021-62794500, 021-62790588
                傳真號碼:021-62792664 公司地址:上海市北京西路1277號國旅大廈1707室

                      <track id="d7dff"></track>

                      <dfn id="d7dff"></dfn>

                          <rp id="d7dff"></rp>

                          <strike id="d7dff"></strike>

                          <cite id="d7dff"><th id="d7dff"></th></cite>